Can you hear the original sound of the CD?Static electricity / charge removal device

The static electricity removal in analog has the effect of reducing the crackling sound of the cartridge, but what about the static electricity removal of the CD board?

You may not even be aware that static electricity is actually generated instead of sucking dust like a record.

However, when you actually remove static electricity and listen to the comparison, you can clearly feel the difference in sound.

The sound will pass better and you can hear the sound of the instrument clearly.

You can feel that the original sound of the charged Disk cannot be reproduced by using this device.

Let's enjoy the original sound of the CD.

Please check the sound of the CD after static electricity removal and static electricity removal.

Did you see the difference by listening to the audition comparison on YouTube?

Before the removal, the sound is rough and a little exaggerated and an excessive sound part can be seen, but after the removal, the sound balance is also good, and

You can feel the three-dimensional effect and presence in the sound.

After all, I think you can confirm that the magnetism of the CD also affects the sound.

And the above audio waveform is the start part of the first song, but you can see the difference in the waveform that you can see visually.

There is no visible difference between the power cable and RCA cable, so how effective is static electricity removal?

And you know that you haven't heard the original sound.

You can see the effect of more than 0 million yen in 30 seconds. Usage is simple.

It has a removal time of about 30 seconds on both sides for about 15 seconds on one side.

If you can't handle it with the ground wire, you can just pick his ground terminal yourself.

The terminals are also picked and removed during audition comparison.

With just this much effort, I think that the sound improvement effect of more than 1 million yen can be seen with accessories such as CD players and cables.

You will be able to enjoy the sound of a sharpened CD.

You can expect a fundamental improvement in sound quality that is different from cables and accessories.

Due to the blackboxing like a CD player, it is no longer possible to customize various items such as cartridges, lead wires, and shells like analog.

First of all, the main focus is on improving external sound quality such as RCA cables, power cables, and insulators.

This item is not an external sound quality improvement like before, but an improvement in the essential part of the source.

And it will be an advantage that you can use it without disturbing the balance of the system you are using now.

I was particular about the simple design.

I don't like the rugged, heavy design and carved aluminum to make it an expensive item, which is typical of audio equipment.

We are trying to create a stylish and simple interior design.

We have finished the design with the minimum number of parts so that you will never get tired of it.

The body with a natural wood finish is handmade!

The body of this device has an MDF-based natural wood oak wood finish.

From the state of the MDF board, we finish it by hand, including assembly, polishing, wood board finishing, polishing, and clear finishing.

There may be some distortion, but I think it is handmade and has a warm and timeless body made of natural wood.

It is powered by AA batteries.

The rotation of the Disc is driven by a single AA battery with a dedicated motor.

It is a clean power supply device that does not affect other audio equipment.

* AA batteries are not included, so please prepare one by yourself.

The drive part uses a motor and a connector for exclusive use of a CD.

For the rotation drive part of the CD, the motor dedicated to the CD and the dedicated connector part used in the commercial machine are used.

The proper voltage of the motor is originally 5.9V, but it is driven at 1.5V with a margin.

And the ground is also attached to the motor afterwards.

Self-discharge + grounding with a silver conductive brush

For static electricity and static electricity removal, we use a silver conductive treatment brush exclusively for professional machines, which is also used in precision machines.

In consideration of durability, only the tip protrudes.

And in order to remove static electricity surely, we apply a grounding method instead of natural discharge.

schedule

We will finish one by one by hand.

Although it depends on the number of orders, we will prioritize finishing over delivery, so please understand in advance that delivery may take longer than planned.

BOX production started in February and March while watching the number of support

March 28, crowdfunding ends

Mid-April Super Early Bird Discount 1,000 Yen off Delivery Start

Early April delivery start 600 yen off Delivery start

Early May delivery start early discount 300 yen off delivery start

Shipping is scheduled to be completed by the end of May or June (may be delayed depending on the number of orders)